Manufacturer: POR-15 Inc., P.O. Box 1235, Morristown, NJ 07962-1235 Telephone: 973-887-1999

PRODUCT NAME: COLORCHROME Two-component transparent dyes FORMULA: Mixture

FLASH POINT (Method used): TCC 80 Degrees F / 27 Degrees C Auto Ignition Temperature: 450 Degrees F / 232 Degrees C

EXTINGUISHING MEDIA: Foam, CO2, Dry Chemical, Sand.

SPECIAL FIRE FIGHTING PROCEDURES/USUAL FIRE OR EXPLOSION HAZARDS: Use of self-contained breathing apparatus should be worn by firefighters (as for all paints). Avoid spreading burning liquid with water for cooling purposes. Keep work areas free of hot metal surfaces and other surfaces and other sources of ignition. FLAMMABLE.

THRESHOLD LIMIT VALUE: For isocyanates, 0.02ppm; for solvent, 200ppm

EFFECTS OF OVEREXPOSURE: Eyes-severe irritation; tearing skin, discoloration-drying; breathing-irritation, dizziness, unconsciousness (for solvent). For isocyanates, coughing, irritation of mucous membranes and respiratory tract.

SKIN EFFECTS: Slight to moderate irritation (MDI); skin sensitizer in guinea pigs (MDI). No conclusive evidence has been developed to indicate that MDI or POR-15 is carcinogenic, teratogenic or that either one causes reproductive effects in animals or humans. MDI has been reported by NIOSH to be mutagenic to Salmonella Typhimurium bacteria in the presence of a mammalian liver activation system. There is not full agreement in the scientific community on the significance of these Ames test results and their relationship to human safety in assessing the risk of cancer in man.

HUMAN EFFECTS OF OVEREXPOSURE: INHALATION – Inhalation of MDI vapors or aerosols in concentrations above 0.02ppm can produce irritation of the mucous membranes in the respiratory tract, running nose, sore throat, productive cough and a reduction of lung function. Extensive exposures to concentrations well above the TLV could lead to bronchitis, bronchial spasm and pulmonary edema. These effects are usually reversible. However, due to low volatility, high exposures are not anticipated except if the material is overheated or sprayed as an aerosol into the air. Hypersensitivity pneumonitis has also been reported. Another type of response is hyper reactivity or hyper sensitization. Persons with a preexisting unspecific bronchial hyper reactivity or persons with a specific isocyanate hypersensitivity (as a result of previous repeated overexposure or a single large dosage) will respond to small isocyanate concentrations at levels well below the TLV level of 0.02ppm. Symptoms could be an immediate or delayed and include chest tightness, respiratory distress or asthmatic attack.

SKIN: Glisten PC reacts with skin protein and tissue moisture and can cause localized irritation as well as discoloration. Prolonged contact could produce reddening, swelling, or blistering and, in some individuals, skin sensitization resulting in dermatitis.

EYES: Liquid, vapors, or aerosols are irritating to the eyes and can cause lachrymation (tearing effect). Corneal damage can occur, however, indications are that the damage is reversible and does not result in permanent injury.

INGESTION: Ingestion could result in irritation and some corrosive action in the mouth, stomach tissue and digestive tract. However, it is not considered a common occupational route of exposure.

EYE CONTACT: Flush with clean, lukewarm water (low pressure) for at least 15 minutes, occasionally lifting eyelids; obtain medical attention.

SKIN CONTACT: Remove contaminated clothing. Wash affected areas thoroughly with soap and water. Wash contaminated clothing before re-use.

INHALATION: Move to an area free from risk of further exposure. Administer oxygen or artificial respiration as needed. Obtain medical attention. Asthmatic-type symptoms may develop and may be immediate or delayed up to several hours. Treatment is essentially symptomatic.

INGESTION: Do not induce vomiting. Give 250 ml of milk or water to drink and refer to medical personnel, or take direction form either a physician or poison control center. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONSIOUS PERSON. Consult physician

EYE PROTECTION: Safety glasses with side shields, splash goggles or face shield. Contact lenses should not be worn.

SKIN PROTECTION: Chemical-resistant gloves. Cover as much of the exposed skin area as possible with appropriate clothing. If skin creams are used, keep the area covered to a minimum.

RESPIRATORY PROTECTION: Use respirator that is recommended or approved for use in isocyanate containing environments (air purifying or fresh air supplied). Consider type of application and environmental concentrations. In spray applications you must protect against exposure to both vapor and spray mist. An air-supplied respirator is strongly recommended for spray application. Observe OSHA regulations for respirator use 29 CFR, 1910.134.

VENTILATION: Ventilation as required to maintain air concentrations below TLV’’s. If material is spray-applied, ventilation should be provided and air supplied respirators worn. Exhaust air may need to be cleaned by scrubbers or filters to reduce environmental contamination.

STABILITY: Stable under normal conditions.

POLYMERIZATION: Will not occur in unopened cans under normal conditions.

CONDITIONS TO AVOID: Temperatures below 32 degrees F (0^oC) or above 122 degrees F (50^oC). To maintain freshness: avoid contact with water, alcohols, amines, strong bases, metal compounds or surface-active materials.

HAZARDOUS DECOMPOSITION (typical of all paints): By fire, carbon dioxide, CO, oxides of nitrogen, traces of HCN, MDI, and elements unknown.

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate source of ignition of vapors, wear protective clothing while cleaning up; absorb on sand, clay, or absorbent material.

WASTE DISPOSAL METHOD: Disposal of in accordance with local, state, and federal regulations. Incineration is preferred. Decontaminate empty containers.

RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator.

EYE PROTECTION: Goggles or facemask.

VENTILATION: Use in well-ventilated areas only. Have adequate general exhaust.

PROTECTIVE GLOVES: Solvent protective gloves.

OTHER PROTECTIVE EQUIPMENT: Self-contained breathing apparatus if threshold limit is exceeded.

STORAGE TEMPERATURE: (min/max): 32 degrees F (0 degrees C) /122 degrees F (50 degrees C).

AVERAGE SHELF LIFE: 12 months @ 77 degrees F (25 degrees C).

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Store in tightly closed container. At maximum storage temperatures noted, material may slowly polymerize without hazard. Ideal storage temperature range is 50-81 degrees F (10-27 degrees C).

REVISED 11/24/05