POR-15 TOPSIDE YACHT ENAMEL

PRODUCT DESCRIPTION

POR-15 TOPSIDE YACHT ENAMEL is a premium-quality state-of-the art polyurethane finish designed for above-the-waterline topsides and decks. One coat, when used with our marine primers, is guaranteed to yield 100% hiding power. As with all POR-15 coatings, POR-15 Topside Yacht Enamel has a higher solids content than any other marine coating.  

SURFACE PREPARATION

Surface must be clean and free of all dirt, rust, oil, grease, wax, soap, loose paint and any other foreign matter. Previously Painted Areas: may be treated with a solution of 2 cups household ammonia in one gallon of water. If mildew is present, remove with household bleach. Be careful never to mix bleach with ammonia. Bare fiberglass: entire surface must be washed with POR-15 Marine Clean® to remove all traces of wax, mold release agents, etc. Next, sand gel coat with 80-120 grit to obtain a dull, flat, matte surface, then wipe clean with dry cloth. Bare wood: Fill screw heads or holes with POR-15 Epoxy Putty, sand smooth, wipe clean with tack cloth, then prime. Bare Steel or Aluminum: Clean surface with Marine Clean, then spray on POR-15 Metal-Ready for 15 – 30 minutes and wash down with water afterwards. After drying surface thoroughly, apply 1 or 2 coats of POR-15 Marine Rust Preventive Paint. Prime when POR-15 is just dry to the touch with slight finger-drag remaining, usually 3 - 4 hours. Primers: For all light topcoats, use POR-15 Light Primer #640 (off-white); for all dark topcoats, use POR-15 Dark Primer #650 (light gray). Use of a primer is critical, but choice of light or dark primer is a relatively unimportant judgment call.

APPLICATION PROCEDURE / PRIMER AND TOPCOAT

Thinning: only if necessary, do not exceed 5%. Coverage: 550 sq. ft. per gallon, 140 sq. ft per quart. Sand: with 220 grit sandpaper between coats. Application temperature range: 50oF to 90oF (10oC - 32oC). Thinner: Use only POR-15 Solvent.. CONTAINS PETROLEUM SOLVENTS: Keep away from heat and flame. To avoid breathing vapors, organic vapor particulate respirators, NIOSH/MSHA approved must be used. Open windows, doors, or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA TC 23C or equivalent) or leave area. Do not smoke during application until all vapors (odors) are gone. To avoid spontaneous combustion during temporary storage, soak soiled rags and waste immediately after use in a water-filled closed metal container. Dry Times: For primers and topcoats to the touch, approx. 2 hours at 75oF. Allow 12 - 15 hours before sanding and top coating. Cleaning Equipment: Use POR-15 Solvent or lacquer thinner. Do not use lacquer thinner for thinning. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN. Notice: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. HARMFUL OR FATAL IF SWALLOWED. DO NOT USE ON

CHILDREN'S’ TOYS, WHICH MAY BE PUT INTO MOUTH. Hazardous Ingredients: Aliphatic Petroleum distillates, Cas #8052-41-3, Titanium Dioxide, Cas #13463-67-7, Oil Modified Polyurethane, Cas # Proprietary Information contained herein is to our knowledge true and accurate, but all recommendations or suggestions are made without guarantee. Since the conditions of its use are beyond our control, POR-15, Inc. disclaims any liability incurred in connection with the use of its products and information contained herein. No person is authorized or empowered to make any statement or recommendation not contained herein, and any such statement or recommendation so made shall not bind the Corporation. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing patents covering any material or its use, and no license implied or in fact is granted herein under the claims of any patents. Contents: